SILICONE-FREE MOULD RELEASE AGENT,
WITH NON-GREASY FILM
NSF H1 CERTIFIED FOR MATERIALS USED IN THE FOOD INDUSTRY
PLASTIC INJECTION MOULD RELEASE
NON-STICK IN LOST WAX FOUNDRIES
MOULD RELEASE FOR COMPOSITES,
FOR COMPRESSION OF PARTICLE BOARD PANELS
PAINTABLE, WELDABLE, ALLOWS ALL SURFACE TREATMENTS
EXCELLENT FINISH AFTER DEMOULDING
DESCRIPTION
DÉMOPLAST® 750 is a mould release agent for plastics. It allows all subsequent coating operations: painting, silk screen printing, bonding, or any decoration.
DÉMOPLAST® 750 has excellent non-stick and lubrication properties, making it an ideal mould release for all manufacturing processes: injection, extrusion, blow moulding, thermoforming or press moulding.
DÉMOPLAST® 750 facilitates the demoulding of materials such as polyamides, ABS, polyurethanes, epoxies, polyesters, and rubbers.
It leaves a very thin, dry film, which does not run. This leads to:
- Easy demoulding, even for the most complicated shapes;
- An excellent surface finish on the demoulded parts (avoiding surface defects such as roughness, streaks, and wrinkles).
It has no effect on most plastics, rubbers, and metallic surfaces.
DÉMOPLAST® 750 does not cause corrosion on moulds.
DÉMOPLAST® 750 facilitates ejection, eliminates problems such as superficial voids and spider web defects on the surface, and produces very high quality surface finishes without roughness, streaks, wrinkles or stains.
DÉMOPLAST® 750 gives excellent results as a non-stick agent to treat precision casting moulds working with the "lost wax" process.
TYPICAL PHYSICAL-CHEMICAL PROPERTIES
|
PROPERTIES |
STANDARD or METHOD |
VALUES |
UNITS |
|
Appearance |
Visual |
Fluid |
- |
|
Saybolt colour |
NF M 07.003 ASTM D 156 |
+10 |
value |
|
Smell |
Olfactory |
No smell |
- |
|
Density at 20°C |
ISO 12.155 |
905 |
g/l |
|
Utilisation temperature range |
- |
-40°C+200°C |
- |
|
Surface tension at 20°C |
ISO 6297 |
25.8 |
dyne/cm |
|
ACTIVE SUBSTANCE PROPERTIES |
|||
|
PROPERTIES |
STANDARD or METHOD |
VALUES |
UNITS |
|
Kinematic viscosity at 25°C |
NF EN 3104 |
1300 |
mm²/sec |
|
Self-combustion point |
ASTM E 659 |
>270 |
°C |
|
Acid index la |
ISO 6618 |
0.0 |
mg/(KOH)/l |
|
Sulphated ash content |
NFT 60,144 |
0.0 |
% |
|
Impurities content larger than 5 µm |
FTMS 791 3005 |
0 |
number/ml |
|
Elastomer compatibility Dimensional variation 168 h at 40°C |
FTM 791 |
less than 0.1 |
% |
|
Environmental properties Bioaccumulation index Octanol/water ratio |
OECD 107 |
less than 3 |
log kOW |
|
Danger category for water |
WGK |
Category 1 no danger for water |
category |
PRESENTATION
|
|
Aerosol 650 ml
|
Product for the food industry (IAA)
Using an HACCP approach or method
Analysis of dangers and critical points to control them
ISO 22 000 CODEX ALIMENTARIUS
Category NSF:
H1 lubricant : usable in food manufacturing areas. Usable as an anti-corrosion agent, non-stick for tank lid seals, lubricant for equipment located in potential food-contact areas.
Looking for another product?
|
Discover our entire IAA range by clicking on the photo |
Manufacturing, lubrification, cleansing, protection,
IBiotec® Tec Industries® Service
offers a wide range of products reserved for industrial area
If you wish for :
a free sample
a technical advice
a product data sheet
a safety data sheet
IBiotec® Tec Industries®Service
manufacturer of technical chemical products.
Welcome to our website.
IBiotec® Tec Industries®Service is on : 